• Colour steel  Roof  waterproofing self-adhesive material
  • Colour steel  Roof  waterproofing self-adhesive material
  • Colour steel  Roof  waterproofing self-adhesive material
  • Colour steel  Roof  waterproofing self-adhesive material
  • Colour steel  Roof  waterproofing self-adhesive material
  • Colour steel  Roof  waterproofing self-adhesive material
  • Colour steel  Roof  waterproofing self-adhesive material
  • Colour steel  Roof  waterproofing self-adhesive material

Colour steel Roof waterproofing self-adhesive material

  1. The self-adhesive coil is made of polymer base material, which does not contain asphalt composition, which overcomes the phenomenon of easy aging, brittle crack and weak bond of asphalt adhesive under the conditions of climate change.

 

  1. Polymer self-adhesive material has good pressure sensitivity, viscosity, creep and self-healing.

 

  1. Polymer non-asphalt based self-adhesive has excellent chemical corrosion resistance (acid, alkali, salt) and anti-aging properties.

 

  1. Self-adhesive waterproof material itself has a better viscosity, a tear a paste, fire roast.

 

  1. The construction method of self-adhesive waterproof coil material is cold construction, the construction process will not use any solvent and fuel, will not use open fire construction, very safe and environmental protection.

 

  1. The selection of heat insulation self-adhesive waterproof coil construction, the requirements for the base is relatively low, the flatness of the requirements will be lower than other coil, at the same time do not need cold bottom oil to do bottom coating, the cost saving.

 

  1. Good durability and aging resistance.

 

  1. Good tensile strength, good flexibility, can actually stick to a variety of irregular roofing.


  • Colour steel  Roof  waterproofing self-adhesive material
  • Colour steel  Roof  waterproofing self-adhesive material
  • Colour steel  Roof  waterproofing self-adhesive material
  • Colour steel  Roof  waterproofing self-adhesive material
Desciption

Determine the key waterproof areas before construction

 

The following area of the color steel tile roof needs to do key waterproof treatment: horizontal lap, vertical lap, roof ridge, sink, color steel tile and parapet junction, screw firmware, color steel tile connection gap and so on for the color steel roof waterproof weak links.

 

Pretrement

Carefully check the color steel roof before construction,determine that the metal roof is firm, clean, no corrosion, no freezing and water ze, do not conform to the above situation is treated as follows;

 

1、Add the firmware in place.

 

2、Using  polishing machine wire grinding wheel or sandpaper grind the loosen rust area,Wash with  pressure water cannon,Clean up the surface then wait surface dry enough,now the surface is free of rust and dust,Remember, we must ensure that the surface is clean and not dirty, otherwise it will affect the construction effect of self-adhesive coil.

 

3、Remove freezing, dust , wipe clean with water, keep the surface clean and dry.

 

  • Check whether the color steel tile has a warping joint, and the warping joint part is fixed firmly with screws and maintained with screws Flat off, otherwise there will be a bulge phenomenon.

 

Construction operation

 

Preparation before construction

Before the construction, the workers first put on safety hats, tie the safety rope, wear good anti-skid Shoes, safety measures in place and then fixed the safety rope at both ends of the color steel tile, fixed the safety rope on the main rope, and check whether the safety rope joint is firm, and check the bearing situation of the color steel tile.

Fix the scaffolding on both sides of the color steel tile eaves, and confirm whether it is firm and firm Solid rear can stand people.

 

In order to ensure the safety of the construction personnel transported to the roof, it is necessary to be lifted The handlebar coil is safely hoisted to the roof.

 

1、When paving the coil, the construction from the water downhill direction(Roof parts)Start  paving.The vertical wall is paved from the height to the bottom.

 

 

2、Eliminate the air, squeeze the air with the coil rolling, and compaction, so that the coil firmly bond.

 

  • The5cm-8cmof long side   and 10cm of  the short side  shoud be overlapped.

Exposed edge and overlap edge should be used with 5cm butyl tape sealed,  Standing wall The header was sealed with 10cm butyl tape.

 

  • Roof nail  position to do a good job, poor treatment will cause bulge. The treatment method can pull out the self-tapping nail , install the protective cap on the self-tapping nail, and then make the waterproof place .Ifthe construction party has a better construction method can also be used.

Safe construction measures

 

1、Before the construction, the workers first fixed the safety rope at both ends of the color steel tile, fixed the safety rope on the main rope, and check whether the safety rope joint is firm, and check the bearing situation of the color steel tile.

 

 

2.Workers before construction first put on safety hats, tie the safety rope, wear good anti-skid Shoes, safety measures in place before the construction.

 

3、Fix the scaffolding on both sides of the color steel tile eaves, and confirm whether it is firm and firm Solid rear can stand people.

 

4、In order to ensure the safety of the construction personnel transported to the roof, it is necessary to be lifted The handlebar coil is safely hoisted to the roof.

Construction instructions and reminders

 

 

1、Clean the surface of the adhesive material before use to ensure that the surface is dry and clean.

2、It is recommended to do waterproof in the water surface construction, and the sand  base surface  is not recommended to use.

3、Tear off the product isolation film, direct adhesion, do not need to fire baking.

4 、When sticking, ensure close adhesion, avoid cracks, bubbles, etc., to ensure the use effect.

5 、Before the construction, the quality of the previous project shall be accepted, and the waterproof layer construction shall be carried out after the qualification.

  • After construction, the bonding effect is enhanced with time. After pasting, the glue layer is physically penetrate into the pores of the base.
Leave a message
FirstName*
LastName*
Email*
Message*